Carbon Fiber Surface Finish
Matte and high-gloss clear coats, UV-resistant coatings and custom surface treatments for durable, consistent carbon fiber finishes.
- UV-Stable
- 2,000h Aging Test
- Custom Texture
Finish Specified, Not Assumed
Surface finish affects weather resistance, appearance and long-term surface protection. We control finish requirements against defined appearance and quality standards.
WITHOUT SPECIFIED FINISH
Unspecified Finish
↓
Inconsistent Appearance
↓
Limited Weather Protection
↓
Variable Quality
WITH CONTROLLED FINISH
Specified Finish
↓
Controlled Process
↓
Verified Weathering
↓
Consistent Appearance
Surface Finishing Capabilities
UV-resistant coating
A UV-resistant carbon fiber coating for parts that sit in the sun — exterior covers, motorsport trim, outdoor equipment. Passed 2,000 hours of aging testing without failing.
High-Gloss Clear Coat
High-gloss appearance with protective clear coating.
Matte Finish
Low-gloss surface for a clean, understated appearance.
Sand blasting
A controlled texture step that evens the surface before coating — or delivers the raw, technical look directly.
Why the finish matters to a buyer
The finish is what your customer touches first. It is also what protects the part for years.
A carbon fiber paint finish is not decoration. It seals the laminate from moisture and chemicals, stops micro-cracks from growing, and carries your brand on every unit. We finish to brand level: visible defects limited to ≤0.03 mm, surface roughness Ra ≤0.8 μm — numbers we measure and record, not adjectives we claim.
Finished in a room built for it
Surface quality starts in the sanding booth, not the spray gun.
Our finishing area runs wet dust-extraction stations, so grinding stays clean for the operator and for the part — airborne dust is pulled away before it settles on a fresh surface. Every sanding stage is followed by inspection, and the surface is checked again before coating. That is how the numbers stay at Ra ≤0.8 μm, batch after batch.
The last pass: carbon fiber polishing
On gloss work, the difference between good and premium is this step.
After coating, high-gloss parts are polished and inspected under light. Carbon fiber polishing removes the last haze, brings out depth, and catches defects before they reach you. What ships is what your customer will see — which is why our appearance inspection checks every part, not one in ten.
Surface Performance Standards
Weathering
2,000-hour aging test
Outdoor Durability
3 years without significant yellowing, aging or delamination
Temperature Range
-40°C to 120°C
Surface Roughness
Ra ≤0.8 μm
Appearance Defects
≤0.03 mm
From Raw Part to Finished Surface
Surface Prep
Surface prepared according to finish requirements.
Finish Application
Clear coat, matte/high-gloss finish, UV coating, sandblasting or silk screening.
Curing / Drying
Controlled according to the selected finishing process.
Final Inspection
Surface appearance and finish quality checked.
Questions about carbon fiber finishing services
Gloss shows depth and weave; matte reads as technical and hides fingerprints. If the part is handled a lot, matte is lower maintenance. We can do either — and show you samples before you commit.
≥3 years, with no significant yellowing after a 2,000-hour aging test.
Gel coat is pigmented and sprayed into the mold before layup; we finish with sprayed clear coats after the part is cured — matte or gloss — which is easier to repair and gives the deep, transparent look carbon fiber is known for. We don't use carbon fiber gel coat on our parts — the clear-coat route keeps the weave visible and stays repairable.
Yes — silk-screen printing is part of our finishing line. Logos, part numbers, and graphics are printed on the prepared surface and covered by the top coat, so they last as long as the finish.
Surface roughness Ra ≤ 0.8 μm and visible defects ≤ 0.03 mm, measured and recorded per batch. If your spec is tighter, we'll confirm it on a sample before quoting.